APLUS features
Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form :(
commands used:  ARCL |
| commands used: BDEL |
| commands used: BLEGEND |
| commands used: BLL0 |
| commands used: BMW |
| commands used: BREMOVE+BADD |
| commands used: CAP |
| commands used: COL |
| commands used: CON1 |
| commands used: COR |
| commands used: DFL |
| commands used: DILINE |
| commands used: DINORM |
| commands used: DIS |
| commands used: DIU_DID |
| commands used: ESC |
| commands used: ESCPL |
| commands used: ESCPL2 |
| commands used: HASSOC |
| commands used: HBET_HBETA |
| commands used: HBO |
| commands used: HD |
| commands used: HLEGEND |
| commands used: HLINE |
| commands used: HM |
| commands used: HOFF_HON |
| commands used: HRO |
| commands used: HTER |
| commands used: HTERM |
| commands used: HTERM2 |
| commands used: HZIG |
| commands used: LAY |
| commands used: LAYC |
| commands used: MALEN |
| commands used: NR |
| commands used: PATTERN |
| commands used: PATTERN_01 |
| commands used: PLAV |
| commands used: PLD |
| commands used: PLEV |
| commands used: PLI |
| commands used: PLJ |
| commands used: PLM |
| commands used: PLP |
| commands used: PLPS |
| commands used: PLRO |
| commands used: PLRO3 |
| commands used: PLS |
| commands used: PLSC |
| commands used: PLT |
| commands used: PLT2 |
| commands used: PLT3 |
| commands used: PLU |
| commands used: PLWELD |
| commands used: RECL |
| commands used: REVISION |
| commands used: RM |
| commands used: RME |
| commands used: RME_2 |
| commands used: RML |
| commands used: RMN |
| commands used: RMNA |
| commands used: RMS |
| commands used: RMSB |
| commands used: SQ |
| commands used: VPP |
 | DRAW: RECTANGLE BETWEEN SELECTED LINES |
| RECL command draws a rectangle (or quadrilateral) between two selected lines or polyline segments. It allows you to close custom shaped holes easily. | |
| commands used: RECL |
 | ARCHITECTURAL: DRAW SLICED LINES |
| Just draw line through objects and APLUS will draw cross-section lines of specified height. | |
| commands used: SLICEL |
 | WALLS: EASILY CREATE CONNECTIONS BETWEEN WALLS |
| You can create cross/tee/corner connections of APLUS walls in seconds. | |
| commands used: WAC , WAT , WAX |
 | WALLS: CAP HOLES |
| You can cap holes in walls just by selecting areas where APLUS will detect holes and eventually cap them. | |
| commands used: CAP |
 | WALLS: CREATE WALLS FASTER |
| APLUS can generate walls with specified thickness from intersecting lines. | |
| commands used: WALLS |
 | WALLS: LINES CONTINOUS OFFSET |
| APLUS can do offset of multiple lines by detecting connections between them. It can be useful when drawing exterior walls. | |
| commands used: LCO |
 | WALLS: LINES CONTINOUS ERASE |
| APLUS can erase multiple lines by detecting connections between them. It can be useful when drawing exterior walls. | |
| commands used: LCE |
 | WALLS: EDITING WALLS |
| Use APLUS to perform basic transformations to existing walls objects (such as moving, rotating), APLUS rooms will be automaticly updated. | |
| commands used: ROWA , COWA , MWA |
