APLUS features
Sie sollen APLUS besser kennen lernen, das ist bestimmt das beste AutoCAD Add-on in der Welt.
Get APLUSdocumentationThank you! Your submission has been received!
Oops! Something went wrong while submitting the form :(
AutoCAD commandline entry:  ALPL |
| AutoCAD commandline entry: ARCL |
| AutoCAD commandline entry: BDEL |
| AutoCAD commandline entry: BLEGEND |
| AutoCAD commandline entry: BLL0 |
| AutoCAD commandline entry: BMW |
| AutoCAD commandline entry: BREMOVE+BADD |
| AutoCAD commandline entry: CAP |
| AutoCAD commandline entry: COL |
| AutoCAD commandline entry: CON1 |
| AutoCAD commandline entry: COR |
| AutoCAD commandline entry: DFL |
| AutoCAD commandline entry: DILINE |
| AutoCAD commandline entry: DINORM |
| AutoCAD commandline entry: DIS |
| AutoCAD commandline entry: DIU_DID |
| AutoCAD commandline entry: ESC |
| AutoCAD commandline entry: ESCPL |
| AutoCAD commandline entry: ESCPL2 |
| AutoCAD commandline entry: HASSOC |
| AutoCAD commandline entry: HBET_HBETA |
| AutoCAD commandline entry: HBO |
| AutoCAD commandline entry: HD |
| AutoCAD commandline entry: HLEGEND |
| AutoCAD commandline entry: HLINE |
| AutoCAD commandline entry: HM |
| AutoCAD commandline entry: HOFF_HON |
| AutoCAD commandline entry: HRO |
| AutoCAD commandline entry: HTER |
| AutoCAD commandline entry: HTERM |
| AutoCAD commandline entry: HTERM2 |
| AutoCAD commandline entry: HZIG |
| AutoCAD commandline entry: LAY |
| AutoCAD commandline entry: LAYC |
| AutoCAD commandline entry: MALEN |
| AutoCAD commandline entry: NR |
| AutoCAD commandline entry: PATTERN |
| AutoCAD commandline entry: PATTERN_01 |
| AutoCAD commandline entry: PLAV |
| AutoCAD commandline entry: PLD |
| AutoCAD commandline entry: PLEV |
| AutoCAD commandline entry: PLI |
| AutoCAD commandline entry: PLJ |
| AutoCAD commandline entry: PLM |
| AutoCAD commandline entry: PLP |
| AutoCAD commandline entry: PLPS |
| AutoCAD commandline entry: PLRO |
| AutoCAD commandline entry: PLRO3 |
| AutoCAD commandline entry: PLS |
| AutoCAD commandline entry: PLSC |
| AutoCAD commandline entry: PLT |
| AutoCAD commandline entry: PLT2 |
| AutoCAD commandline entry: PLT3 |
| AutoCAD commandline entry: PLU |
| AutoCAD commandline entry: PLWELD |
| AutoCAD commandline entry: RECL |
| AutoCAD commandline entry: REVISION |
| AutoCAD commandline entry: RM |
| AutoCAD commandline entry: RME |
| AutoCAD commandline entry: RME_2 |
| AutoCAD commandline entry: RML |
| AutoCAD commandline entry: RMN |
| AutoCAD commandline entry: RMNA |
| AutoCAD commandline entry: RMS |
| AutoCAD commandline entry: RMSB |
| AutoCAD commandline entry: SQ |
| AutoCAD commandline entry: VPP |
 | DRAW: RECTANGLE BETWEEN SELECTED LINES |
| RECL command draws a rectangle (or quadrilateral) between two selected lines or polyline segments. It allows you to close custom shaped holes easily. | |
| AutoCAD commandline entry: RECL |
 | DRAW: RECTANGLE WITH SPECIFIED AREA |
| RECA command allows you to draw rectangle with specified area. APLUS will ask for start point and then give you live preview of the rectangle. | |
| AutoCAD commandline entry: RECA |
 | ARCHITECTURAL: DRAW RAMP |
| APLUS can help you design a ramp for underground parking. APLUS decides where to break ramp to make it usable. | |
| AutoCAD commandline entry: RAMP |
 | POLYLINES: DRAW PART OF POLYLINE CONTAINED INSIDE OTHER ONE |
| APLUS can draw part of polyline which lays inside another polyline. | |
| AutoCAD commandline entry: PLIN |
 | POLYLINES: DRAW CEILING HOLE SYMBOL FROM SELECTED POLYLINE |
| With PLHO command you can draw ceiling hole symbol from selected polyline. APLUS will create new, closed polyline. | |
| AutoCAD commandline entry: PLHO |
 | HATCHES: DRAW HATCH BOUNDARY |
| HBO command can draw boundary of selected hatch pattern. This may help you recover some lost information from a drawing. | |
| AutoCAD commandline entry: HBO |
 | PLUMBING: DRAW DUCTS |
| After setting some parameters you may easily design ducts both inside and outside buildings. | |
| AutoCAD commandline entry: DUCT |
 | POLYLINES: MOVE, ROTATE OR SCALE MULTIPLE POLYLINE SEGMENTS |
| PLM command allows you to move multiple polyline segments at once. PLRO rotates polyline segments and PLSC scales them. With these commands you may modify polylines freely. | |
| AutoCAD commandline entry: PLM , PLRO , PLSC |
 | DIMENSIONS: MEASURE TOTAL LENGTH |
| TLENGTH command measures and displays total length of selected objects. It can measure length of nearly all AutoCAD object types. | |
| AutoCAD commandline entry: TLENGTH |
 | DRAW: DRAW 2D AXONOMETRIC PROJECTION SIMULATION |
| AXO command can draw simulation of axonometric projection of specified objects. | |
| AutoCAD commandline entry: AXO |
 | POLYLINES: DRAW POLYLINE CONTINUATION |
| PLCO command draws continuation of selected polyline. Command will start drawing from the closest end to selection point. | |
| AutoCAD commandline entry: PLCO |
 | POLYLINES: ROTATE POLYLINE SEGMENT |
| ROPL command can rotate selected polyline segment without affecting rotation angle of other segments. | |
| AutoCAD commandline entry: ROPL |
 | WERKZEUG: POSITION DES OBJEKTES AN DIE LINIEN AUSRICHTEN |
| Der Befehl ALO ermöglicht es, die Position des ausgewählten Objektes an die Linien auszurichten. Die Polylinien werden durch das gedrückte Segment ausgerichtet. | |
| AutoCAD commandline entry: ALO |
 | POLYLINES: DRAW BOUNDARY OF POLYLINE WITH SET WIDTH |
| With APLUS you may easily draw boundary of polyline with set width. Command PLBO allows you to transform sketches made with thick polylines into normal polylines. | |
| AutoCAD commandline entry: PLBO |
 | TEXTS: EXPLODE TEXT OR MTEXT OBJECT |
| TX command allows you to explode any TEXT or MTEXT object. As a result APLUS will create new polyline objects in place of exploded TEXT or MTEXT object. | |
| AutoCAD commandline entry: TX |
 | POLYLINES: DOUBLE POLYLINE / ALIGN POLYLINE SEGMENT |
| With PL2 you can draw double polyline. You may specify width and justification. ALPL is a tool to align polyline segment to extension of a line or a polyline. You can fill closed polyline with termal insulation hatch with HTERM. | |
| AutoCAD commandline entry: PL2 , ALPL , HTERM |
 | POLYLINES: FILLET POLYLINE |
| APLUS allows you to fillet any polyline. You can specify fillet radius. Original polyline will be preserved. | |
| AutoCAD commandline entry: FPL |
 | POLYLINES: CHAMFER POLYLINE |
| APLUS allows you to chamfer any polyline. You can specify chamfer radius. Original polyline will be preserved. | |
| AutoCAD commandline entry: CHAPL |
 | POLYLINES: MOVE POLYLINE'S SEGMENT |
| APLUS allows you to move segment of a polyline without changing any of its angles. | |
| AutoCAD commandline entry: MPL |
 | DIMENSIONS: MEASURE POLYLINE |
| APLUS can quickly measure selected polyline. | |
| AutoCAD commandline entry: DIPL |
 | POLYLINES: 2D/3D ROOF FROM POLYLINE |
| Create 2D or 3D roof from selected polyline | |
| AutoCAD commandline entry: PLROOF |
 | POLYLINES: SHADOW |
| APLUS will draw simulated shadow of specified object on specified direction with specified lenght. | |
| AutoCAD commandline entry: PLSHADOW |
 | |
| APLUS can simulate one-point perspective of selected object from specified vanishing point. | |
| AutoCAD commandline entry: PLPERS |
 | POLYLINES: UNION |
| Create object that will contain area of both original objects. | |
| AutoCAD commandline entry: PLU |
 | POLYLINES: INTERSECTION |
| Create object that will contain only the area that was common to both original objects. | |
| AutoCAD commandline entry: PLI |
 | POLYLINES: SUBTRACTION |
| New object will contain area of original object with intersection area subtracted from it. | |
| AutoCAD commandline entry: PLS |
 | POLYLINES: TRIM POLYLINES |
| Use APLUS to trim overlaping areas. | |
| AutoCAD commandline entry: PLT |
 | POLYLINES: CLOSE POLYLINES |
| Use APLUS to enclose polyline objects. Missing part will be created if needed. | |
| AutoCAD commandline entry: PLC |
 | POLYLINES: UNWARP SELECTED POLYLINE |
| Create polyhedron net from selected polyline (base). | |
| AutoCAD commandline entry: PLUNWARP |
 | POLYLINES: CONVERT POLYLINE'S SEGMENT TO ARC |
| Select segment of polyline to convert it into arc. | |
| AutoCAD commandline entry: PLARC |
 | POLYLINES: CONVERT POLYLINE'S SEGMENT TO ARC |
| Select segment of polyline to convert it into arc. | |
| AutoCAD commandline entry: PLW , PLWS |
 | POLYLINES: JOINING POLYLINES |
| Use APLUS to join multiple polylines. | |
| AutoCAD commandline entry: JJ |
 | POLYLINES: PURGE POLYLINES |
| Purge selected polyline from verticles placed too close. | |
| AutoCAD commandline entry: PLP |
 | POLYLINES: CONNECT NEAREST POINT(S) OF TWO PLINES |
| Use APLUS to quickly connect two separate polylines on both or just nearest end | |
| AutoCAD commandline entry: CONN |
